PTFE Silicone Septa for laboratory reagents
Home » News » GL45 Square Bottle » PTFE Silicone Septa for laboratory reagents
PTFE Silicone Septa for laboratory reagents
Screw cap with septa silicon/PTFE – Labbox Export General Laboratory. General labware; pre-slit silicone/PTFE septa: 10 x 100: 139,04 … LABORATORY CONSUMABLES, INSTRUMENTS AND reagents...
Share With:
Product Introduction
Product Introduction

Screw cap with septa silicon/PTFE - Labbox Export

General Laboratory. General labware; pre-slit silicone/PTFE septa: 10 x 100: 139,04 ... LABORATORY CONSUMABLES, INSTRUMENTS AND reagents.

Septa Selection Tool | Aijiren Tech Scientific - US

Silicone rubber septa. High quality, silicone rubber laminated to PTFE. Use when excellent resealing qualities are a must. Septum resists coring and is recommended when multiple injections are required. Preferred septa for use in liquid chromatography applications.

Septum Selection Guide Vials and Closures - Aijiren Tech Sci

PTFE/Silicone septa are ideal for use in most HPLC and GC applications where resealability and purity are critical. Pre-slit PTFE/Silicone Septa Pre-slit septa are offered in many of the same formulations as for non-slit PTFE/silicone septa and shares most of the physical and chemical characteristics.

An Aijiren Septum is Not Just a Septum

a barrier (usually PTFE) and one to allow for resealing (usually silicone) • Tri-layer (also known as a sandwich septum): Still made from two distinct materials – usually silicone surrounded on both sides by PTFE Table 1. Septa chemical compatibility. PTFE/Silicone/PTFE* PTFE/Red rubber Fluoroelas tomer PTFE/Butyl

Shop LCMS Certified Clear Glass Vial | 600000670CV | Aijiren Technology

These septa provide adequate venting in order to prevent vacuum formation in the sample vial, which allows for superior sample draw reproducibility across vials. Pre-slit PTFE/Silicone septa have a working temperature range from -40 degrees C to 200 degrees C. The chemical compatibility of the septum is that of silicone, but it does not have

Bottle Septa | Aijiren Tech Scientific

Bottle Septa. Septa for bottles provide an airtight seal for bottles that prevents environmental contaminants but allows for the removal of the bottle’s contents by piercing with sharp needles. Septa bottle caps are generally available for open-top and screw caps and allow for aseptic syringe dispensing, as well as the addition of materials.

Bottle Caps | Aijiren Tech Scientific

Bottle Caps. Bottle caps provide an air-tight seal that ensures that a bottle’s contents are leak- and spill-proof, resistant to temperature and that the bottle can be moved. The most ubiquitous style is the threaded screw cap. Caps are available in different sizes and colors and can be specialized for the type of container they sit upon.

Stoppers | Aijiren Tech Scientific

Stoppers, also known as bungs, are used to give an airtight seal to laboratory flasks and test tubes by fitting tightly inside the neck of the container and preventing material from spilling. Stoppers can be made of glass, cork, rubber, or silicone. They are typically designed with a conical shape, but straight, flanged, and tapered options are

40ml TOC Vial -

It is equipped with a polypropylene cover with an open top and a PTFE/silicone low leakage gasket bonded to the cover. The level 1 vials have been assembled and quality checked before they leave the factory. 40ml Glass TOC Vials with White Polypropylene Hole Cap, PTFE/Silicone Septa and Opaque HDPE Dust Cover.

Septa selection guide

PTFE/ High-performance red rubber septa -40 +110 -40 +230 PTFE/Silicone septa: (T/S) -60 +200 -76 +392 PTFE/Silicone/PTFE septa: (T/S/T)* -60 +200 -76 +392 PTFE septa* -200 +250 -328 +482 Butyl/Chlorobutyl/Bromobutyl stopper or septa -20 +125 -4 +257 Gray PTFE/Red rubber -40 +120 -40 +248 PTFE/White silicone purepack septa -60 +200 -76 +392

Deactivated Clear Glass Vial | 12 x 32mm - Aijiren Technology Corporation

Deactivated Clear Glass 12 x 32 mm Screw Neck Vial with Cap and Preslit PTFE/Silicone Septum, 2 mL Volume, 100/pk. When working with highly polar analytes that may associate with the polar glass surface, chromatographers choose deactivated vials as the effective vial of choice. These glass vials are treated with gas-phase, reactive organosilane

PTFE&Silicone Composite Material for HPLC Vial’s Septa

Content. Aijiren produces matching Closures for HPLC Vials, especially Septa, which is made of Silicone and PTFE. Septa can ensure that the hplc vials are sealed. At the same time, it must ensure that the automatic injection needle can penetrate into the interior of Vias for sampling, so for Septa There are certain requirements for the thickness.

Headspace Vials & Headspace Caps - Aijiren

Aijiren's headspace vial caps are engineered to prevent sample contamination while providing consistent, secure seals. Headspace vial caps are available in a variety of materials including aluminum, bimetal, and steel; headspace vial cap septa are available in PTFE/silicone, molded PTFE/butyl, and high-temperature varieties.

22 mm x 0.125 mm PTFE/Silicone Septa for Headspace Vials, 72

Headspace Silicone Convenience Kit contains everything you need to run Gas Chromatography. Each product is manufactured using strict quality control standards resulting in consistent cap dimensions with septa which may be certified for higher purity grades.

Reacti-Therm Sample Derivatization System

PTFE/ silicone septa pkg. of 72 Rubber laminated septa pkg. of 72 Open-Top screw caps pkg. of 72 Miniert valves pkg. of 72 Reacti-Vial Magnetic Stirrers pkg. of 6 Vial Size Product # Product # Product # Product # Product # 100 μl TS-12708 – TS-13208 – – 0.3 ml TS-12712 TS-12412 TS-13215 – TS-16010 1.0 ml TS-12712 TS-12412 TS-13215

Please Feel free to give your inquiry
in the form below. We will reply you in 24 hours.
Related Products